Toad Cat 1 (Ai 606)
3 posts
|Page 1 of 1
RE: Re: RE: I HATE 56K
Ok, So I removed my Cat1 from my dead motor and I marked up all the wires(What a very frustrating time I had), Then installed it in to my new motor(soldered and heatshrinked all connections).
I seem to have every thing working ok apart from the bonet/boot sensor, I mean It locks up the car,goes off when it should and so on, But when arming it, It flashes 5 times indicating the bonnet or boot is insecure.
I have swapped the bonnet plunger from my old car(worked fine on it) I have checked the boot plunger(light goes off when pressed) But still have 5 flashs when arming!!!!!!!!!!!!!!!.
I phoned the local car elec place and they said -: it could be because you still have the Aftermarket immob wired up or that you still have the Standard vauxhall alarm/immob wired up and having two lots of sonic sensors is fudging up the system!!!
The guy from the shop said to disconnect the vaux ECU for the alarm/immob(Passenger footwell bolted in on the left), Problem fixed so far as the 5 flashes went, But now the car won't start because the various immobs on it!!!!!!
I get all all ignition lights but no turn over(indicating the Starter motor ciruit has a block somewhere)
Am I disconnecting the correct control module?????????????????Cos the manual says sommut about a module on the drivers side for the alarm.
I am getting really frustrated as I only know basic electronics and can't figure out what the f**k is wrong, Can you please help?????
Cheers Mac..
I seem to have every thing working ok apart from the bonet/boot sensor, I mean It locks up the car,goes off when it should and so on, But when arming it, It flashes 5 times indicating the bonnet or boot is insecure.
I have swapped the bonnet plunger from my old car(worked fine on it) I have checked the boot plunger(light goes off when pressed) But still have 5 flashs when arming!!!!!!!!!!!!!!!.
I phoned the local car elec place and they said -: it could be because you still have the Aftermarket immob wired up or that you still have the Standard vauxhall alarm/immob wired up and having two lots of sonic sensors is fudging up the system!!!
The guy from the shop said to disconnect the vaux ECU for the alarm/immob(Passenger footwell bolted in on the left), Problem fixed so far as the 5 flashes went, But now the car won't start because the various immobs on it!!!!!!
I get all all ignition lights but no turn over(indicating the Starter motor ciruit has a block somewhere)
Am I disconnecting the correct control module?????????????????Cos the manual says sommut about a module on the drivers side for the alarm.
I am getting really frustrated as I only know basic electronics and can't figure out what the f**k is wrong, Can you please help?????
Cheers Mac..
-
Mac
RE: Head Unit not working
Problem solved now!!,
Took about 2hrs of coffee/tabs and the hynes manual wiring diagrams.
The fault was my instalation with one wire!!
From the vaux alarm modual their are three wires which have the same colour and tracer colour??, two negs and one pos, I had connected the wrong neg wire up, so a quick clip clip with a solder here and thier, bit of electrical tape and Bobs your uncle Franks your aunt,
Every thing is now pucka!!!!!
Cheers all the same
MAC. [img]/smile.gif[/img]
Took about 2hrs of coffee/tabs and the hynes manual wiring diagrams.
The fault was my instalation with one wire!!

From the vaux alarm modual their are three wires which have the same colour and tracer colour??, two negs and one pos, I had connected the wrong neg wire up, so a quick clip clip with a solder here and thier, bit of electrical tape and Bobs your uncle Franks your aunt,
Every thing is now pucka!!!!!
Cheers all the same
MAC. [img]/smile.gif[/img]
-
Mac
3 posts
|Page 1 of 1
Who is online
Users browsing this forum: No registered users and 16 guests